3D Printer Egypt Control Board Mikromake MAKEBAORD 1.4 RAMPS Compatible

SKU: MAKEBOARD1.4
Out of stock
EGP 950.000
Out of stock
Brand:Chinese

Description

Introduction:

Makeboard Pro is specially designed by Micromake Technical Team to solve the problem which usually occurs on the open source control board of Ramps 1.4 3d printers.
We had fully consider about the mistakes that customers usually make in the beginning, so we use different color to distinguish different connector, and use XH connector to avoid reverses.
We give enough protection in the circuit program. The board adopt dual self-recovery fuses to avoid short-circuit and 5-way high resistance diode to avoid reverse so you will not damage the board even if the wire of power sully is insert oppositely.
The design of Pin is compatible with RAMPS 1.4 control board, you can download the open source firmware of Marlin or Repetier and so on to use directly. The default type of control board is this board.
With 3-way temperature sensing, 4-way MOS output, 5-way motor drive and support big power heatbed as well. What’s more, it support dual extruder! Meanwhile, it can support 5v, 12v-24v fan.
5-way motor drive signal all leads which support connecting with High Power Motor Driver to make huge size 3d printer.
Support 1602,2004,12684 display, insert EXP1, EXP2 connector, meanwhile , with AUX1 connector the touch color screen is available.
The size of this board is 10*10cm, the 4 setting hole use M3 screws, the center of the hole is 5mm far from the edge.

Note:

The matched drive board use fool-proofing design, it has blue pin header on the left and black on the right in case overheating due to anti-plug.
If you use other control board or drive board, please note the triangle arrowhead at the top left corner is ENABLE definition and plug correspondingly.
It supports 128 microstep resolution at most and can be adjusted by MS1, MS2, MS3 jumper in the center of drive board socket. H means short circuit, and L means disconnecting.
If you need to adjust current, please put the positive electrodes of multimeterinto screw hole on adjustable resistor and put negative electrodes on USB shell after restarting printer.
The measured voltage divided by 0.8 equals current of drive chip. Eg: If the default voltage is 0.6V, the current is 0.6/0.8=0.75A.
Please be sure to cut off power first, then rotate adjustable resistor with screwdriver. Turn left to decrease the value, turn right to increase the value. Don’t screw too much at one time, 30°is OK.
Turn on the power after adjustment, then measure the voltage, if it isn’t appropriate, please cut off the power and adjust again. It is recommended to make XYZ motor 0.75A, E motor 1A.

Package includes:

1 x Makeboard Pro

Micromake® Makeboard Pro 3D Printer Main Board Support Heatbed Compatible with Ramps 1.4

Micromake® Makeboard Pro 3D Printer Main Board Support Heatbed Compatible with Ramps 1.4

Features:
  • Marlin or Repetier compatible (RAMPS 1.4 compatible)
  • 4-way MOSFET output
  • 5-way motor drivers with support for 128 microstep resolution (voltage divided by 0.8 = drive current)
  • Supports dual extruder
  • Support for 5V, 12-24V fans
  • Support for 1602, 2004, 12864 displays using EXP1/EXP2 connectors
  • TFT display supported with AUX1 connector
  • Recoverable fuse for short-circuit protection
  • 10cm x 10cm footprint
  • You can see related material and course on official Makeboard website: https://www.makeboard.org

Additional information

Weight 0.025 kg

Brand

Chinese

Chinese
Chinese

Reviews

There are no reviews yet.

Be the first to review “3D Printer Egypt Control Board Mikromake MAKEBAORD 1.4 RAMPS Compatible”

Refund Policy for UGE Electronics “Https://uge-one.com “

 

1. Returns and Refunds

Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.

 

2. Eligibility for Refund

To be eligible for a refund, please make sure that:

– The item was purchased in the last 14 days.

– The item is in the original packaging.

– The item isn’t used or damaged.

 

3. How to Initiate a Refund

To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.

 

4. Refund Processing Time

Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.

If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.

 

5. Shipping Costs

Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.

 

6. Exchanges

If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.

 

7. Damaged or Defective Items

If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.

 

8. Contact Information

If you have any questions about our Refund Policy, please contact us at [[email protected]].

 

Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.

Product Enquiry

Please Login to make enquiry about this product