No products in the cart.
Altera USB Byte Blaster Cable USB Programmer & Debugger Rev C
Out of stock
EGP 345.000 exc. vat
Out of stock
Brand:Chinese
Description
Altera USB Byte Blaster Cable USB Programmer & Debugger Rev C
Brand new and high quality.
Fully compatible with original Altera USB-Blaster.
Supported target voltage : 1.0V-5.5V.
Support all ALTERA deveice.
CPLD：MAX 3000A、MAX 7000A、MAX 7000B、MAX 7000S、MAX 9000、MAX 9000A and MAX II.
FPGA：Stratix、Stratix II、Stratix GX、Cyclone、Cyclone II、Cyclone III、ACEX 1K、APEX II、APEX 20K、APEX 20KE、APEX 20KC、FLEX 10K、FLEX 10KE、FLEX 10KA、FLEX 6000、FLEX 8000、EPCS1、EPCS4、EPCS16、EPCS64EPC1、EPC4、EPC8、EPC16.
Support：JTAG, AS, PS Mode.
Support NiosII embeded core based debug.
Supports Quartus II SignalTap? II Logic Analyzer (for logic analysis).
High performance, 6 times faster than ByteBlasterII.
USB interface with status and Power LED.
Size:5.5cm x 2.8cm x 1.5cm – 2.17inch x 1.1inch x 0.59inch.
Package Included:
1 x USB BLASTER Programmer
1 x USB cable
1 x 10-Pin JTAG Connection Cable
1 x USB cable
1 x 10-Pin JTAG Connection Cable
Additional information
| Weight | 0.006 kg |
|---|
Brand
Chinese
Chinese
Chinese
You must be logged in to post a review.
Y leads 30cm 22awg Futaba Servo Motor High Quality Flat Cable Wire
EGP 30.000 exc. vat Add to cart
JM20330APCO-TGCA Serial ATA Bridge Chip TQFP64
EGP 210.000 exc. vat Add to cart
SMD Chip Resistor size 0603 270R 270 Ohm
EGP 0.250 exc. vat Add to cart
SN74LS02 Quad 2 input NOR Gate TTL 5V Logic IC
EGP 15.000 exc. vat Add to cart
Blue Tape Sheet 30×30 Cm For 3D Printer
EGP 45.000 exc. vat Add to cart
Refund Policy for UGE Electronics “Https://uge-one.com “
1. Returns and Refunds
Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.
2. Eligibility for Refund
To be eligible for a refund, please make sure that:
– The item was purchased in the last 14 days.
– The item is in the original packaging.
– The item isn’t used or damaged.
3. How to Initiate a Refund
To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.
4. Refund Processing Time
Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.
If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.
5. Shipping Costs
Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
6. Exchanges
If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.
7. Damaged or Defective Items
If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.
8. Contact Information
If you have any questions about our Refund Policy, please contact us at [[email protected]].
Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.
Product Enquiry
Related products
AVR USBtinyISP USBTiny ISP programmer
EGP 150.000 exc. vat Add to cart
3D Printer PCB Mk2 HeatBed
EGP 170.000 exc. vat Read more
3D Printer RAMPS 1.4 Arduino Mega Shield for a RepRap
EGP 220.000 exc. vat Read more
AVR USB JTAG ICE Programmer, Emulator and Debugger
EGP 225.000 exc. vat Read more
Reviews
There are no reviews yet.