Description
- Working voltage: 5V DC
- Working current: 3.8mA
- Working temperature: 0~+70 degrees
- Output mode: analog voltage (0~Vcc)
- Induction angle: less than 15 degrees
- Detection range: 2cm-300cm
- Detection accuracy: 0.3cm+1%
- Resolution: 1mm
The size of the module: 45mm*20mm*1.2mm.
After the module is powered up, the system first determines the input level of the Range pin, and sets the different range according to the input level. When the Range pin is high, the range is 3m, when the Range pin is low, the range is 1m.
US-016 ultrasonic ranging module
1. Outline
US-016 ultrasonic ranging module can achieve 2cm ~ 3m non-contact distance measurement function, the supply voltage of 5V, operating current of 3.8mA, support for analog voltage output, stable and reliable. This module can be set to different ranges according to different scenarios (maximum measurement distance respectively 1m and 3m); when the Range pin is floating range is 3m.
US-016 can measure the distance into an analog output voltage, output voltage is proportional to the measured distance.
2. The main technical parameters
Electrical parameters
|
US-016 ultrasonic ranging module
|
Operating Voltage
|
DC 5V
|
Working current
|
3.8mA
|
Operating temperature
|
0 ~ + 70 degrees
|
output method
|
Analog voltage (0 ~ Vcc)
|
Induction angle
|
Less than 15 degrees
|
Detection range
|
2cm-300cm
|
Detection accuracy
|
0.3cm + 1%
|
Resolution
|
1mm
|
The size of the module: 45mm * 20mm * 1.2mm. The board has two radius of 1mm mechanical holes, as shown below:
From left to right are numbered 1,2,3,4. They are defined as follows:
L 1 Hao Pin: connected to VCC power supply (DC 5V).
L 2 Hao Pin: range setting pin (Range), when the module is powered up when this pin is high, the range of 3m; when the module is powered up when this pin is low, the range of 1m. Within this pin pull-up resistor, when the Range pin floating, the range is 3m.
L 3 Hao Pin: analog voltage output pin (Out), an analog voltage proportional to the distance measurement, the output range is 0 ~ Vcc.
L 4 Hao Pin: connected to an external circuit.
5. Ranging works
After the power module, the system first determines Range pin input level to set different ranges depending on the input level of the state.When the Range pin is high, the range is 3m, when the Range pin is low, the range is 1m.
Then, the system begins continuous ranging, while the ranging results in an analog voltage output pin Out. When the change in distance analog voltage will also vary.
Additional information
Weight | 0.007 kg |
---|
You must be logged in to post a review.
END Support Pillow Block Bearing 8mm KFL08
SMD Chip Resistor size 1206 15R Ohm
Oscilloscope 60MHz Hantek DSO1060
DIODE 1N4148 Small Signal Fast Switching
Refund Policy for UGE Electronics “Https://uge-one.com “
1. Returns and Refunds
Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.
2. Eligibility for Refund
To be eligible for a refund, please make sure that:
– The item was purchased in the last 14 days.
– The item is in the original packaging.
– The item isn’t used or damaged.
3. How to Initiate a Refund
To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.
4. Refund Processing Time
Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.
If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.
5. Shipping Costs
Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
6. Exchanges
If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.
7. Damaged or Defective Items
If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.
8. Contact Information
If you have any questions about our Refund Policy, please contact us at [[email protected]].
Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.
Reviews
There are no reviews yet.