Dual DC Motor Driver 7A 160 Watt Module / board H Bridge L298 logic
Description
Dual DC Motor Driver 7A 160 Watt Module / board H Bridge L298 logic
Functional characteristics:
1. Very small size, only if 5.5 cm * 5.5 cm
2. Support voltage from 7V to 24V, undervoltage protection
3. Dual motor interface with rated output current 7a
4. Similar to L298 control logic, each line supports three wire control, positive reverse and brake
5. The signal enable can be externally connected to the PWM, and the positive and negative control signals can be connected in series with the limit switch
6. Control signals use the current driving mode, which supports most single-chip direct drives
7. All control signals are isolated using an optical connector
8. ESD circuit
Technical specifications:
1. Voltage range: Input: DC 6.5 V-27 V
2. Rated input voltage: 12V / 24V DC
3. Output Channel Number: 2
4. Rated output current per channel: 7A
5. Maximum output current per channel: 50A
6. Rated output power per path: 84 W (12 V), 168 W (24 V)
7. Pilot signal voltage: 3 ~ 6.5 v
8. Line control signal current: 3 ~ 11 mA
9. Support PWM frequency range: 0 ~ 10 kHz
10. Minimum Effective Pulse Width PWM: 10 US
11. Operating temperature: 25 ℃ ~ 80 ℃
12. Size: 5.5 cm × 5.5 cm × 2.0 cm
Suitable for engine parameters:
• Rated motor voltage 24 V, rated power 115 W and below the correct logo or logo below 7A Rated motor current full working long time
• Motor rated voltage 12 V, rated power 40 W and below the correct logo or logo below 7A Rated motor current full working long time
Additional information
Weight | 0.02 kg |
---|
You must be logged in to post a review.
Arduino Uno R3 & Acrylic Base & Mini BreadBoard Kit
0805 SMD Chip Resistor 20k
SMD Chip Resistor size 1206 300K Ohm
Pin Header Male 2×40 Straight 2.54mm
Refund Policy for UGE Electronics “Https://uge-one.com “
1. Returns and Refunds
Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.
2. Eligibility for Refund
To be eligible for a refund, please make sure that:
– The item was purchased in the last 14 days.
– The item is in the original packaging.
– The item isn’t used or damaged.
3. How to Initiate a Refund
To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.
4. Refund Processing Time
Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.
If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.
5. Shipping Costs
Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
6. Exchanges
If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.
7. Damaged or Defective Items
If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.
8. Contact Information
If you have any questions about our Refund Policy, please contact us at [[email protected]].
Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.
Reviews
There are no reviews yet.