Menu
Shopping Cart
Check UGE Offers on all products Shop now

Designed By UGE

Designed By UGE

Designed By UGE

Manufactured Via UGE

Assembled By UGE

This category contains all products designed , manufactured and  Assembled by UGE Electronics.

USB to Dual TTL UART COM Ports Converter Module CH340 Compatible Drivers
New
Brand: UGE Electronics Model: MOD-1102
HighlightsThis is USB to serial module based on the CH340G Drivers. It is commonly used to debug various TTL serial devices, upgrade the firmware of routers, It's a small USB to TTL serial tool, You can use it to connect some serial device to your PC via USB port.the Module uses Typical USB C..
106.00EGP
Brand: Chinese Model: BOX 19x14x6 PS
Project Enclosures Box 19x14x6 cm Laser Cut MDF 3mm (Can customize it according to your specific needs) with Mounting holes for LEDs, output banana connector, Potentiometers ,and the rear side contains Fan air slots...
63.60EGP
Brand: UGE Electronics Model: RFID-RC522-V1
OverviewThis is based on RF module RC522 near field communication module. Its working frequency is 13.56MHz and you can read and write a 13.56MHz tag with this module. Features: - Very easy to use with the library for Arduino - Operating voltage: 3.3V. - Interface logic level: compatible wi..
143.10EGP
Brand: UGE Electronics Model: MOD-041
MCP2551 CAN Protocol Controller High-speed Interface ModuleFeature:Support 1MB / S's run rate.Meet the ISO-11898 standard physical layer requirements.Suitable for 12V and 24V systems. Slope external control, reduce RFI.Automatically detects TXD input ground fault.Power-on reset and voltage brown-out..
95.40EGP
Arduino Nano V3 Enhanced Version with USB type-C and Stamp holes pins
SOLD OUT
Brand: UGE Electronics Model: ard-nano-3-New
The new SMD Arduino nano with stamp holes, half-hole immersion gold technology, high-end atmosphere and high-grade, very exquisite! Notice! This version does not have the two pins A6 and A7, and the rest are exactly the same as the usual nano. Technical parameters: 1. 12 digital input..
222.60EGP
ESP32 Development Board For IOT Attendance Projects
SOLD OUT
Brand: UGE Electronics Model: ESP32-RFID-KIT
 ESP32 Development Board for IoT based RFID Attendance System Board Features:Header for ESP32 ModuleHeader for 0.96” OLED Display Connected to I2C pins of ESP32 (D22,D21)Header for RC522 Module. Connected to SPI pins of ESP32 (D2,D18,D23,D19,D5)Relay Circuit to control ..
514.10EGP
Brand: UGE Electronics Model: IR-38KHZ-TXRX-Mod
The module contains 4 infrared transmitters and an integrated infrared receiver. The four infrared transmitters are responsible for converting the electrical signals into optical signals for transmission. The integrated infrared receiver is responsible for converting the optical signals into electri..
84.80EGP
AC main Isolated detector module 5V and 3.3V output level compatible
-20 %
Brand: UGE Electronics Model: MOD-1101
Isolated AC mains Voltage Detection Features:Isolated voltage detection is vital in many industrial applications. Isolation is a means of preventing direct or alternating currents between two parts of a device, while allowing signal and power transfer between those two parts. Isolation also manages ..
55.00EGP 68.90EGP
16 Channels Relay Module for ESP32 IOT Development Board
-8 %
Brand: UGE Electronics Model: WIFI-16RELAY
INTRODUCTION:In order to meet the customer's demand for the control of the switching device, we releases a ESP32  Compatible 16-channel relay module which allows a small level signal to control any normal outlet or high voltage This is a 12V 16-Channel Relay interface board, be a..
600.00EGP 650.00EGP
Brand: UGE Electronics Model: mod-485-3.3V
OverviewOn-board RS485 chip is a low-power and slew-rate-limited transceiver used for RS-485 communication. It works at a single +3.3V power supply and the rated current is 300 μA. Adopting half-duplex communication to implement the function of converting TTL level into RS-485 ..
53.00EGP
ESP8266 ESP12 ESP01 USB programmer board with spring pogo pins
Check Availability
Brand: UGE Electronics Model: ESP-programmer
The USB ESP12 and ESP01 programmer can flash ESP12 modules in circuit without having to desolder them first. It features spring pogo pins to be directly pressed onto the ESP.You can connect a USB cable (not included) to it and use Arduino IDE, PlatformIO or others to upload code. It features a RESET..
201.40EGP
Showing 1 to 12 of 41 (4 Pages)