Menu
Your Cart
Check UGE Offers on all products Shop now

Modules & Accessory Boards

Modules & Accessory Boards

Microcontroller Addon modules is a modulated, ready-to-use tool set. Much like Lego, it takes a building block approach to assembling electronics. Compared with the traditional, complicated learning method of using a breadboard and various electronic components to assemble a project, so this simplifies and condenses the learning process significantly. 

Model: MOD-061
40W DC-AC inverter 12V rise 220V step-up transformer boost module module inverter transformer This product is a high-frequency current, not ordinary multimeter test voltage, you need a professional high-frequency multi-table before the test can be obtained voltage. You test out different brand..
85.00LE
Model: MOD-059
This is for one power module for controlling 3D printer heated bed, it is also can be used to drive other non-inductive loads. If you plan to use silicone heater of large area heated bed, you most likely will overcome limitations for the current, that can handle your current 3d printer&nbs..
120.00LE
Model: MOD-011
Features: ADC Bit rate: 16 Bit Interface Type: I2C Channels: 4 Channel AN0 AN1 AN2 AN3 or 2 differential inputs Input voltage: 2.0-5.5v Channel input voltage :0-VDD Continuous Mode: Only 150μA Single-Shot Mode: Auto Shut-Down PROGRAMMABLE DATA RATE:8sps-860sps Input range programmed control, 7 typ..
75.00LE
Model: SEN-049
Introduction This Vibration Sensor buffers a piezoelectric transducer that responds to strain changes by generating a measurable output voltage change which is propotional with the strength of vibration.   Specification Power supply: Not necessary to power the mo..
40.00LE
Model: ARD-M02
Basic Information Product     status:  NEW   production company: Special for UGE   Type     Number: LY-SD00101   Product     Name: SD card module   ..
60.00LE
Model: ard-tft-2.8-2
Product Features: Size: 2.8 inches Driver chip: ILI9341 Touch type: no touch Resolution: 240 * 320 Communication Interface: SPI   Pin definition: GND ( power ground ) VCC ( power supply is 3.3V) CLK ( clock line ) MOSI ( data ..
235.00LE
Model: ARD-M01
Introduction This is a Micro SD(TF) module. It is compatible with TF SD card (commonly used in Mobile Phone) which is the most tiny card in the market. SD module has various applications such as data logger, audio, video, graphics. This module will greatly expand the capbility an Arduino can do wit..
45.00LE
Model: ARD-MP3-1
INTRODUCTION The MP3 Player Mini is a small and low cost MP3 module with an simplified output directly to the speaker. The module can be used as a stand alone module with attached battery, speaker and push buttons or used in combination with an Arduino UNO or any other with RX/TX capabilities. ..
165.00LE
Model: mod-bb-PS
Overview This is a power module for the standard bread board. Its concave design will not waste your proto zone. This breadboard power shield supports Mini USB power supply and power jack 7-12V supply. There are two independent power optional: 5V/3.3V. With this board, you can send power to both po..
25.00LE
Model: mod-ch375b
Overview CH375B is a USB bus general interface chip with 8-bit data bus and control lines for reading, writing and chip selection and output interruption, which can be easily attached to the system bus of controllers such as MCU / DSP / MPU. In USB host mode, CH375B also provides serial co..
120.00LE
Model: Mod-016
The new 1.44-inch Serial SPI TFT color LCD module Pixles: 128X128! Driver: ST7735 Only four IO can drive and use! onboard level translation chip IC, Super compact structure, cost-effective 1.44-inch serial module, you deserve!..
150.00LE
Model: MOD-024
    Input voltage: DC1-5V (1.5V or more is recommended as well) Output voltage: 12V fixed Size: Length 25mm * wide 16mm * 6mm high Conversion rate: 90% (maximum) Load power consumption: 3-15mA    The maximum continuous output power of 4W, then high temperature, and the ..
35.00LE
Showing 1 to 12 of 69 (6 Pages)