PCA9685 16-channel 12-bit PWM/Servo Driver I2C module
Description
You want to do a cool robot, maybe want to do a six-legged walking robot, or just a piece of art with many moving parts. You may also want to use precise PWM output drive many LED indicator. Then you realize that your microcontroller PWM limited number of output!What will happen next? You can give up or you can use this handyPWM servo drive small plate.
Introduction:
This is a communication using i2c, built-in PWM driver and a clock.This means that this will be very different from the TLC5940 series.You do not need to constantly send signals to take up your microcontroller!
It is 5V compatible, which means you can also use 3.3V MCU control and safe drive to 6V output (when you want to control the white or blue LED with a positive voltage of 3.4 + is also possible)
6 address selection pin allows you to 62 drive board hanging in a single i2c bus, a total of 992 PWM output. That would be a very large resource.
About 1.6Khz adjustable frequency PWM output
12-bit resolution for stepper motor output, which means that the update rate of 60Hz can reach 4us resolution
Configurable push-pull output or open-circuit output
The output enable pin enables fast disabling of all outputs
characteristic:
l Central PCA9685 chip was wrapped in a small plate
l power input terminals
l green power indicator
l allowing you to group 3 at 4 pin connector 16 is inserted in a servo motor (servo motor plug slightly wider than the 0.1 “, so you can put four pairs of 0.1” connector)
l reverse polarity protection terminal board input
l cascade design
L V + line to place a large capacitor (in some cases you’ll need) the maximum voltage depends on the peripheral input capacitance 10V1000uf
l All PWM output lines have put a 220 ohm series resistor to protect them, and can easily drive the LED.
Additional information
Weight | 0.021 kg |
---|
You must be logged in to post a review.
0805 SMD Chip Resistor 47k
SMD Breakout Adapter PCB Board for TQFP 32~100 Packages
RCD Tester Kyoritsu 5406A
DHT11 Temp/Humidity Sensor Module
TJA1021T LIN Bus transceiver SMD SOP8
Refund Policy for UGE Electronics “Https://uge-one.com “
1. Returns and Refunds
Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.
2. Eligibility for Refund
To be eligible for a refund, please make sure that:
– The item was purchased in the last 14 days.
– The item is in the original packaging.
– The item isn’t used or damaged.
3. How to Initiate a Refund
To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.
4. Refund Processing Time
Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.
If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.
5. Shipping Costs
Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
6. Exchanges
If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.
7. Damaged or Defective Items
If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.
8. Contact Information
If you have any questions about our Refund Policy, please contact us at [[email protected]].
Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.
Reviews
There are no reviews yet.