Description
Model |
Solar30-24 |
Solar30-48 |
||
Rated operating current |
20A |
30A |
20A |
30A |
Rated operating voltage |
12V / 24V |
48V |
||
Solar panel voltage |
≤ 50V |
≤ 100V |
||
Float voltage |
13.8V / 27.6V |
55.2V |
||
Undervoltage protection |
10.7V / 21.4V |
42.8V |
||
Voltage recovery |
12.5V / 25.0V |
50.0V |
||
Load loss |
≤ 30mA |
≤ 30mA |
||
Circuit voltage drop |
≤ 170mV |
≤ 170mV |
||
Charge Mode |
PWM mode |
|||
Temperature Compensation |
-4mV / Cell / ° C |
|||
Installation:
1. Prepare relevant tools and cables. We recommend that you matching the right cable, to ensure that the current density < 4A / mm2 this will help to reduce the line pressure drop. Recommended: 30A with 10mm2 cable.Check the installation site meets the relevant safety regulations, avoid damp, dusty, there is a flammable and corrosive gas installation using the controller.
2. The solar controller is fixedly mounted to the vertical plane, installation aperture and hole spacing see section V. In order to ensure good heat dissipation controller, please reserve at the bottom of each controller 10cm space.
3. As ” CM30 installation wiring diagram “shown in sequence to load, batteries, solar panels connected to the controller up, pay attention to ensure that the load, battery, solar panel polarity consistent with the controller.
4. The external temperature sensor probe is inserted into the left side of the controller temperature probe interface, and battery temperature probe placed in similar places. (Otherwise, the controller will control parameters of the temperature compensation of the error.)
5. As with the remote monitoring function, set the supplied communication cable between the communications port and the other end connected to the controller to the right of the host computer.
Removal: To prevent accidents, in the order when removing the solar panels, batteries, controller disconnects the load.
Note: Battery reverse polarity will not damage the controller, but will your load device is a security risk.
Additional information
Weight | 0.03 kg |
---|
You must be logged in to post a review.
Tiva C Series TM4C123G TI LaunchPad EK-TM4C123GX Evaluation Kit
FP6298 Low-Noise 4.5A Step-Up Current Mode PWM Converter IC SMD SOP8
Refund Policy for UGE Electronics “Https://uge-one.com “
1. Returns and Refunds
Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.
2. Eligibility for Refund
To be eligible for a refund, please make sure that:
– The item was purchased in the last 14 days.
– The item is in the original packaging.
– The item isn’t used or damaged.
3. How to Initiate a Refund
To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.
4. Refund Processing Time
Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.
If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.
5. Shipping Costs
Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
6. Exchanges
If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.
7. Damaged or Defective Items
If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.
8. Contact Information
If you have any questions about our Refund Policy, please contact us at [[email protected]].
Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.
Reviews
There are no reviews yet.