Xilinx FPGA development Spartan6 XC6SLX9 Spartan-6 advanced board
Description
Introduction
The purpose of this manual is to describe the functionality and contents of the AX309 development board. This document includes instructions for operating the board, descriptions of the hardware features, and explanations of the test code programmed into the on-board programmable memory. For reference design documentation and example projects.
Description
The AX309 development board provides a complete hardware environment for designers to accelerate their time to market.The kit delivers a stable platform to develop and test designs targeted to the low-cost and low-power Xilinx Spartan-6 FPGA. The installed Spartan-6 FPGA LX9 device offers a prototyping environment to effectively demonstrate the enhanced benefits of low-cost Xilinx FPGA solutions. Reference designs are included with the kit to exercise standard peripherals on the evaluation board for a quick start to device familiarization.
The AX309 development board contains the following individual pieces:
–The easyFPGA-Spartan-6 development board
–USB 2.0 cable
–Xilinx ISE® Design Suite (IDS) 14.7
–Example Source Code
–AX309 Development Board Users Manual
—Transparent protection board
Please note that this kit does NOT include a Xilinx programming cable.
FPGA
–Xilinx Spartan-6 XC6SLX9 FPGA
JTAG Port
–On-board JTAG Port for programming
SDRAM
–256Mbit SDRAM
SPI Flash memory
–64Mbit SPI FLASH
Camera Port
–Supports 5000000 pixels OV5640 module
Pushbutton switches
–4 User Keys
–Normally high; generates one active-low pulse when the switch is pressed
General User Interfaces
–4 User LEDs
–6-digit 7-segment displays
–Buzzer
System Clock inputs
–50MHz oscillator
RTC Module
–Comes with a CR1220 battery socket
External Eeprom
–Comes with a 24LC04;
VGA output
–Uses a 16-bit resistor-network DAC under RGB65536 Mode
–With 15-pin high-density D-sub connector
Voltage Regulator Circuit
–Provides 1.2V,5V and 3.3V for system power supply
Micro SD
–Equips a Micro SD card holder.
On-board USB to TTL/RS232 Module
–Use cp2102 for USB-TTL/RS232 Converting (Without DB-9 serial connector)
40-PIN Expansion Headers
–Two Channels 40-PIN Expansion Headers Spartan-6 I/O pins, as well as 3 power and ground lines, are brought out to the 40-pin expansion connectors. You can install 4.3”TFT module and AD/DA module by our company on this two expansion headers.
What’s on Board
A photograph of the AX309 development board is shown in following Figure 3. It depicts the layout of the board and indicates the location of the connectors and key components.
The following hardware is provided on the AX309 development board:
Tab1.Baord Source
1 |
Xilinx XC6SLX9 |
2 |
256Mbit SDRAM |
3 |
FLASH 16Mbit |
4 |
USB to UART cp2102 |
5 |
USB/USB Power |
6 |
Power Switch |
7 |
JTAG Port |
8 |
Camera Port |
9 |
VGA Port |
10 |
SD card |
11 |
RTC DS1302 |
12 |
Reset and 4 User Buttons |
13 |
6-digit LED Display |
14 |
EEPROM 24LC04 |
15 |
4 User LEDs |
16 |
50Mhz System Clock |
17 |
Buzzer |
18 |
Power Circuit |
19 |
40PIN Expansion Port |
20 |
40PIN Expansion Port |
Additional information
Weight | 0.36 kg |
---|
You must be logged in to post a review.
Refund Policy for UGE Electronics “Https://uge-one.com “
1. Returns and Refunds
Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.
2. Eligibility for Refund
To be eligible for a refund, please make sure that:
– The item was purchased in the last 14 days.
– The item is in the original packaging.
– The item isn’t used or damaged.
3. How to Initiate a Refund
To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.
4. Refund Processing Time
Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.
If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.
5. Shipping Costs
Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
6. Exchanges
If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.
7. Damaged or Defective Items
If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.
8. Contact Information
If you have any questions about our Refund Policy, please contact us at [[email protected]].
Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.
Reviews
There are no reviews yet.