No products in the cart.
3D Printer RAMPS All in One plus “Complete 3D printer electronics in one Board”
Out of stock
EGP 850.000 exc. vat
Out of stock
Brand:Chinese
Description
Features
Based Arduino 2560, RAMPS 1.4 pin compatible pin configuration, All in one solution for ultra-small, especially for MINI-type machines and new users in 3d printer build.
Provide a heating end, 240W MAX (where the range depends on the MOS parameters)
Support hot bed 240W MAX (maximum current does not exceed 10A, the proposed temperature control in 100 ℃ below)
Power supply: 12 or 24V DC (can use laptop power supply or other switching power supply)
Two thermometers (thermistor) inputs, one for the thermal head and one for the hot bed
Six-way limit switch, 3 min, 3 max (non-cost considerations recommended the use of six switches to avoid collision)
Reserved I2C expansion port, ESP-01 WIFI module interface, user-friendly to add functionality
All the way adjustable fan interface, two power connector (can be used for fixed output fan or LED and other equipment)
On-board 4-way two-phase stepper motor drive (based on Allegro A4988, maximum current limit 1.0A)
TF on-board deck, and perpendicular to the board, beautiful and convenient place
Integrated 2.4 inch 12864 display, can be realized in Chinese or English display (depending on the firmware may be)
Here you can Downlaod the FirmWare
Recommended with:
12-24V DC switching power supply (without hot bed 90W +, with hot bed 200W +) X 1
NTC 100K (default B value of 3950, or other specifications) Thermistor (line length according to the machine) X 2 (with two hot beds, without a hot bed like)
Drying tube 12-24V / 40W
Hot bed / not more than 100 ± 10W X 1
12-24V fan X 1 [(can also connect two parallel), for surface cooling when printing, but also increase the fan as the motherboard or the motor cooling]
A number of wires
SD card X 1
42 stepper motor (1.0A max) X 4 (or 5, Z-axis motor in parallel)
Wiring diagram:
Description:
1. The output voltage of the thermal head, hot bed and FAN / LED, PWM fan is equal to the input voltage. When using 12V power supply
These interfaces are 12V, 24V power supply when using these interfaces are 24V
2. Limit switch is connected to S (signal terminal) / GND for mechanical limit switch (also connect to S (signal terminal) / GND / 5V, for photoelectric switch, at this time need to remove the white seat Son to welding pin)
3.I2C interface, from left to right as follows: SCL, SDA, GND, 5V
Additional information
| Weight | 0.025 kg |
|---|
Brand
Chinese
Chinese
Chinese
You must be logged in to post a review.
LDR Photoresistor 12mm
EGP 10.000 exc. vat Add to cart
Carbon Resistor 0.25W 1.2K Ohm
EGP 0.250 exc. vat Add to cart
DIY Robot Tracks Tanks Closed Rubber Belt Pair Crawler Wheel Accessories
EGP 135.000 exc. vat Add to cart
Mini Momentary Push Button Switch
EGP 5.000 exc. vat Read more
Coils 1/4 Watt 22mH
EGP 2.000 exc. vat Read more
Refund Policy for UGE Electronics “Https://uge-one.com “
1. Returns and Refunds
Thank you for shopping at UGE Electronics “Https://uge-one.com “. If you are not entirely satisfied with your purchase, we’re here to help.
2. Eligibility for Refund
To be eligible for a refund, please make sure that:
– The item was purchased in the last 14 days.
– The item is in the original packaging.
– The item isn’t used or damaged.
3. How to Initiate a Refund
To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.
4. Refund Processing Time
Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.
If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.
5. Shipping Costs
Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
6. Exchanges
If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.
7. Damaged or Defective Items
If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.
8. Contact Information
If you have any questions about our Refund Policy, please contact us at [[email protected]].
Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.
Product Enquiry
Related products
Hall sensor proximity switch NJK-5002C NPN normally open
EGP 55.000 exc. vat Read more
A4988 Stepper Motor Driver 2A
EGP 65.000 exc. vat Read more
3D Printer Electronics Standard Kit MK1
EGP 750.000 exc. vat Read more
3D Printer External SD Memory Module for Ramps Board
EGP 95.000 exc. vat Read more
Reviews
There are no reviews yet.