CH554G USB microcontroller with 16KB ROM/ 256-bytes IRAM/ 1.25Kbytes XRAM and DMA

SKU: D20-11-2
In Stock
EGP 75.000
In Stock




  • Core: enhanced e8051 core, compatible with MCS51 instruction set. 79% of its instructions are single byte single cycle instructions. The average instruction speed is 8-15 times faster than the standard MCS51. It has a special xram data replication instruction and double dptr pointer.
  • ROM: 16 KB capacity of multi programmable non-volatile memory ROM, can be used for all program storage space
  • Data Flash: 128 bytes multi erasable non-volatile data memory, which supports rewriting data in bytes.
  • RAM: 256 bytes internal RAM, which can be used for fast data storage and stack; 1.25K bytes on chip xram can be used for large amount of data temporary storage and DMA (direct memory access).
  • USB: embedded USB controller and USB transceiver, supporting USB device mode and Host Mode, master-slave detection, supporting USB 2.0 full speed 12mbps or low-speed 1.5mbps. FIFO is built-in and supports 64 bytes of data packets.
  • Timer: three groups of timers, t0 / T1 / T2 is the standard MCS51 timer.
  • Capture: timer T2 is extended to support 2-way signal capture.
  • PWM: 2 sets of PWM output, pwm1 / pwm2 is 2-way 8-bit PWM output.
  • UART: asynchronous serial port, support higher communication baud rate, UART0 is the standard MCS51 serial port.
  • SPI: SPI controller has built-in FIFO, clock frequency up to half of the system’s main frequency Fsys, supports serial data input and output simplex multiplexing, and supports master / slave mode.
  • Touch key: 4-channel capacitance detection, support independent timing interrupt.
  • GPIO: supports up to 17 GPIO pins (including Xi / XO, RST and USB signal pins).
  • Interrupt: supports 14 groups of interrupt signal sources, including 6 groups of interrupts (INT0, T0, INT1, T1, etc.) compatible with standard MCS51 UART0, T2), and extended 8 groups of interrupts (spi0, tkey, USB, ADC, uart1, pwmx, GPIO, wdog), in which GPIO interrupt can be selected from 7 pins.
  • Watch dog: 8 bits can preset watchdog timer wdog, support timing interrupt.
  • Reset: support 4 kinds of reset signal source, built-in power on reset, support software reset and watchdog overflow reset, optional pin external input reset.
  • Clock: built in 24 MHz clock source, which can support external crystal by multiplexing GPIO pins.
  •  It supports low-power sleep, USB, UART0, uart1, spi0 and part of GPIO external wake-up.
  • The chip has a unique ID number.

Additional information

need to Customize this product?





There are no reviews yet.

Be the first to review “CH554G USB microcontroller with 16KB ROM/ 256-bytes IRAM/ 1.25Kbytes XRAM and DMA”

Refund Policy for UGE Electronics “Https:// “


1. Returns and Refunds

Thank you for shopping at UGE Electronics “Https:// “. If you are not entirely satisfied with your purchase, we’re here to help.


2. Eligibility for Refund

To be eligible for a refund, please make sure that:

– The item was purchased in the last 14 days.

– The item is in the original packaging.

– The item isn’t used or damaged.


3. How to Initiate a Refund

To initiate a refund, please contact our customer support at [[email protected]] or [01066552125]. Provide your order number and details about the product you would like to return.


4. Refund Processing Time

Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item.

If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer’s policies.


5. Shipping Costs

Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.


6. Exchanges

If you wish to exchange an item, please contact our customer support. You will be responsible for the return shipping costs, and we will cover the shipping costs of the replacement item.


7. Damaged or Defective Items

If you received a damaged or defective product, please contact us immediately for assistance. We will work with you to resolve the issue promptly.


8. Contact Information

If you have any questions about our Refund Policy, please contact us at [[email protected]].


Important Note: This Return & Refund Policy is applied only for Orders invoiced VIA UGE Electronics, and regarding any Orders has been invoiced VIA any Other Vendor you can check the Return & Refund Policy of this Vendor VIA the Vendor Stroe Page, and it’s not our responsibility for any issue between you and the Vendor.

Product Enquiry

Please Login to make enquiry about this product